⚠️ Important: Please ensure you are running SmartZone v3.0 or above to continue.
📌 Note: This guide is for SmartZones using the non-API configuration. If you are using the Northbound API, refer to our other SmartZone guide.
Guest WiFi configuration
To configure the Guest WiFi via Ruckus SmartZone log in to your SmartZone web interface, then follow each of the sections below in order.
RADIUS set up
To configure your RADIUS servers, follow the steps below:
Click Services & Profiles and then click Authentication on the left.
Click the Proxy (SZ Authenticator) tab then Create and configure with:
Name: Guest RADIUS.
Service Protocol: RADIUS.
Primary Server IP Address: 18.168.231.87.
Port: 1812.
Shared Secret: Please contact Support.
Confirm Secret: Please contact Support.
⚠️ Important: Ensure that there are no spaces before and after the RADIUS secret.
Backup RADIUS: Enable Secondary Server.
Secondary Server IP Address: 18.134.223.213.
Port: 1812.
Shared Secret: Please contact Support.
Confirm Secret: Please contact Support.
⚠️ Important: Ensure that there are no spaces before and after the RADIUS secret.
Click OK to save.
Next, click Accounting on the left. Click the Proxy tab, then Create and configure with:
Name: Guest RADIUS Acct.
Primary Server IP Address: 18.168.231.87.
Port: 1813.
Shared Secret: Please contact Support.
Confirm Secret: Please contact Support.
⚠️ Important: Ensure that there are no spaces before and after the RADIUS secret.
Backup RADIUS: Enable Secondary Server.
Secondary Server IP Address: 18.134.223.213.
Port: 1813.
Shared Secret: Please contact Support.
Confirm Secret: Please contact Support.
⚠️ Important: Ensure that there are no spaces before and after the RADIUS secret.
Click OK to save.
Hotspot and walled garden set up
To configure the guest hotspot, follow the steps below:
Click Hotspots & Portals on the left. Click the Hotspot (WISPr) tab then Create and configure with:
Portal Name: Guest Wi-Fi
Smart Client Support: None
Login URL: External
Redirect unauthenticated users to (Primary):
Redirected MAC Format: AA-BB-CC-DD-EE-FF
HTTPS Redirect: ON
Start Page - Redirect to the following URL:
Scroll to the Walled Garden section and add all of the following walled garden domains. There may also be other relevant regional accounts if your venue is outside of the UK or US that you will need to add.
Click OK to save.
Wireless LAN set up
To configure your WLAN, follow the steps below:
Click Wireless LANs on the left, then click Create.
Under General Options, configure with:
Name: Guest Wi-Fi.
SSID: e.g. _Venue Name Guest Wi-Fi - or whatever you wish.
Zone: Select a zone.
WLAN Group: Select a group or default.
Under the Authentications Options section, configure with:
Authentication Type: Hotspot (WISPr).
Method: Open.
Under the Encryption Options section, configure with:
Method: None.
Under the Hotspot Portal section, configure with:
Hotspot (WISPr) Portal: Guest WiFi.
Bypass CNA: Off.
Authentication Service: ON - Use Controller as proxy.
From the dropdown select the RADIUS profile previously configured - i.e. Guest RADIUS.
Accounting Service: ON - Use Controller as Proxy -
From the dropdown select the RADIUS Accounting profile previously configured - i.e. Guest RADIUS Acct.
Send interim update: every 2 Minutes.
Under the RADIUS Options section, configure with
NAS ID: AP MAC
Delimiter: Dash
Single Session ID Accounting: ON
Called Station ID: AP MAC
Click Ok to save.
Insights Plus Ruckus location services set up
There are two steps to this process; the initial step adds the Wireless Social MQTT broker to the SmartZone and sets this up. The second step enables this for the zone in question which then pushes out the configuration to the Access Points. Follow the instructions below to complete:
On SmartZone click System Menu, then select General Settings and the Location Services tab.
Click on Create and you will see a new menu box Create LBS Server. Enter the below details:
Venue Name: v6a
Server Address: rx1-proxy.wireless-social.com
Port: 8883
Password: ruckusws2022
Press OK to save the details.
To deploy the settings to your Zone, follow the steps below:
Go to Access points in the left-hand menu and click Access Points.
Choose the zone to deploy to - e.g. the Default one if your controller does not have multiple zones.
Choose Configuration and press configure.
Scroll down to the bottom – and click on Advanced to open extra options.
Scroll down to Location Based Services and choose V6a - this is the venue identifier entered in the first steps.
Save your changes.
⚠️ Important: Don't change the venue name, or the password – these must match the ones on our systems for data to be processed.
Notify Support once you have completed the configuration and we can monitor for data coming in.
Your login and Insights Plus presence data will appear in the Insights portal within 24 hours.